Output component
Confirm what case making & inner laminating lines must deliver to the next production operation.
Equipment category
Case Making & Inner Laminating Lines
Case Making & Inner Laminating Lines. Compare the production step before selecting a machine family.
Equipment category review
Define what case making & inner laminating lines must achieve.
A case making and inner laminating line decision starts with the real product, complete format range, material specification, accepted-output target and the operation that receives the result.
Supplied visual evidence
Equipment and process references
These supplied equipment images support process discussion. Confirm the exact model revision, guarding, options and configuration in the current written offer.
Image source: materials supplied for this project. Product, machine and facility identity must be confirmed against the current quotation before making a contractual claim.
Catalogue-backed comparison
Compare linked case-making and lining configurations.
Use the values below for initial screening. Final fit requires the current technical offer and an actual-material sample trial.
Catalogue speed is a published machine range, not a promise of accepted production output. Product format, material behavior, changeover and inspection criteria must be tested.
One linked flowCase making, transfer, inner-paper gluing, positioning, laminating and flattening.
700 and 1000 formatsCatalogue maximum sizes extend from 450x700 mm to 600x1050 mm.
Trial requirementConfirm the complete case and liner combination, not each operation in isolation.
| Model | Maximum / minimum size | Catalogue speed | Positioning | Power |
|---|---|---|---|---|
| QZFM-700K | 450x700 / 100x200 mm | 20-30 pcs/min | ±0.2 mm | 30 kW |
| QZFM-1000K | 600x1050 / 140x240 mm | 20-30 pcs/min | ±0.25 mm | 34 kW |
| QZFM-700B-II | 450x700 / 100x200 mm | 20-35 pcs/min | ±0.1 mm | 30 kW |
| QZFM-1000B-II | 600x1050 / 140x240 mm | 20-30 pcs/min | ±0.1 mm | 34 kW |
| QZFM-700B | 450x700 / 100x200 mm | 20-30 pcs/min | ±0.1 mm | 42 kW |
| QZFM-1000B | 600x1050 / 140x240 mm | 20-30 pcs/min | ±0.1 mm | 42 kW |
Source: HORDA 2026 equipment catalogue supplied for this project. Confirm the latest machine revision before ordering.
Decision framework
Three checks for case making & inner laminating lines.
Use these checks to keep the case making and inner laminating line discussion tied to measurable inputs, outputs and responsibility boundaries.
Working range
Check minimum, maximum and frequent jobs instead of one nominal case making and inner laminating line format.
Acceptance result
Judge case making & inner laminating lines by consecutive accepted pieces, not maximum catalogue speed alone.
Information for review
Prepare a complete case making and inner laminating line brief.
The six items below reduce assumptions when evaluating case making & inner laminating lines and make competing technical offers easier to compare.
Required componentRecord this item specifically for case making & inner laminating lines rather than relying on a generic machine request.
Minimum formatGive the minimum, maximum or current condition that applies to the case making & inner laminating lines project.
Maximum formatAttach a drawing, photograph, specification or physical sample relevant to case making & inner laminating lines.
Frequent jobsState how this case making & inner laminating lines requirement will be inspected and accepted.
Registration needExplain present production, job mix and the expected change connected with case making & inner laminating lines.
Downstream processConfirm who supplies, approves and supports this part of the case making & inner laminating lines scope.
Project sequence
Move case making & inner laminating lines from sample to written scope.
Keep the same product definition, material set and acceptance method throughout the case making and inner laminating line trial, quotation and order.
01Define the output component for Case Making & Inner Laminating Lines
02Measure the complete job range for Case Making & Inner Laminating Lines
03Test material and registration for Case Making & Inner Laminating Lines
04Record accepted output for Case Making & Inner Laminating Lines
05Confirm written scope for Case Making & Inner Laminating Lines
Frequently asked questions
Questions about case making & inner laminating lines.
Use the answers as a starting checklist and confirm project-specific statements with current technical evidence.
How do I choose among case making & inner laminating lines?
Start with the output component, flat size range, material set, registration need, job mix and the next production operation.
Is maximum speed the main selection criterion?
No. Accepted output, changeover, minimum format, process quality, labor and line balance can be more important.
What is needed for an accurate quotation?
Provide samples, flat drawings, material details, size range, target output, electrical standard and desired supply scope.
Can existing equipment be integrated?
Often yes, but interfaces, heights, buffers, control responsibility and acceptance of the combined line must be reviewed.
Primary topic: case making and inner laminating line. This page remains excluded from search while its facts, images and application proof are under review.
Explore next
Related planning pages.
Continue from case making & inner laminating lines to the most relevant equipment, process, application or buyer-information page.